None

For the following research paper assignment, you have been asked to perform an evaluation of employee exposures at a small automobile parts manufacturing facility. The manufacturing processes include two metal presses, two machining stations, three welding stations, a small paint booth, and a shipping/receiving area. There are two employees working at each press, one person working at each machining station, one person working at each welding station, two people working in the paint booth, and four employees working in the shipping/receiving area. One of the presses is a 2,000-ton press, and the other press is a 200-ton press. The 2,000-ton press is the greatest noise source for the facility. The machining area uses a metal working fluid. The safety data sheet (SDS) for the metal working fluid is attached here. All welding is performed on stainless steel. The painting booth uses a powder coating operation, but the employees use xylene and methyl ethyl ketone (MEK) to clean the parts prior to the powder coating operation. At the end of the shift, one of the employees uses 1,3 butadiene to clean the nozzles for the paint booth. The facility uses two electric forklifts to move materials between the production area and the storage warehouse and between the warehouse and the shipping area. All employees work an 8-hour shift.

Part 1: Using the information on anticipation and control we studied in the textbook, identify the hazards that are present in the facility. In your discussion, explain why you chose the hazards, and describe whether you believe the hazards to be actual hazards or potential hazards (which require further evaluation). Describe the specific location(s) at the facility where the hazards are located, and determine how many employees are potentially at risk in those areas. Your response for Part 1 should be at least one page in length.

Part 2: Using the information on evaluation that we studied in the textbook, summarize how you would measure the personal exposures to the hazards that you identified in Part 1. Use the Occupational Safety and Health Administration (OSHA) website (https://www.osha.gov/dts/sltc/methods/toc.html) or the National Institute for Occupational Safety and Health (NIOSH) website (http://www.cdc.gov/niosh/docs/2003-154/default.html) to select the specific sampling and analytical method that would work best to evaluate any chemical hazards you identified. Provide a summary of the sampling media you would use, include the sampling flow rate, discuss how long you would sample, and explain how you would calibrate the sampling train. Include a discussion about why you selected the specific sampling and analytical method.

Part 3: Access the attached sampling results here. For each set of results, perform the following actions: Calculate the 8-hour time weighted average (TWA) exposure. Compare the results to the appropriate OSHA permissible exposure limit (PEL). Determine which results exceed an established OSHA PEL. Write a one-page summary of the sampling results; document the exposures that exceeded an OSHA PEL, and identify those areas that you believe will require the application of controls to reduce risk. Include your calculations, include a list of the OSHA PELs you compared the results to, and explain how you decided that an exposure exceeded an OSHA PEL.

Laboratory Results for Unit VIII Research Paper

Employee Position Analyte Sample Time Sample Result 1 Machining Mineral oil mist 480 minutes 1.1 mg/m3 2 Machining Mineral oil mist 480 minutes 0.9 mg/m3 3 Welding Cleaning Hexavalent chromium 360 minutes 120 minutes 8.5 µg/m3 0.5 µg/m3 4 Welding Cleaning Hexavalent chromium 300 minutes 180 minutes 10.0 µg/m3 0.2 µg/m3 5 Paint Booth Xylene MEK 480 minutes 24 ppm 60 ppm 6 Paint Booth/Cleaning Nozzles 1,3 butadiene 15 minutes 6.0 ppm

Noise Dosimetry Data

Employee Position Sample Time Sample Result 1 Setting up parts for press Operating 2,000-ton press Clean-up 60 minutes 400 minutes 20 minutes 82.0 dBA 100 dBA 80.0 dBA 2 Setting up parts for press Operating 200-ton press Clean-up 30 minutes 430 minutes 20 minutes 80.0 dBA 89.0 dBA 80.0 dBA 3 Machining 480 minutes 85.5 dBA 4 Paint Booth 480 minutes 80.5 dBA 5 Shipping/Receiving/Forklift Driver 480 minutes 82.0 dBA

Part 4: Using OSHA’s hierarchy of controls, recommend the control methods that you believe would be the most effective for reducing the risks associated with the exposures that exceeded the OSHA PEL above. Explain how you would implement the controls and how you would evaluate the effectiveness of the controls. Also, discuss any interim control methods you would recommend for the facility. This section should be at least one page in length. Include a reference page and in-text citations for all sources you used in this project, including your textbook, using proper APA format.

 

"Are you looking for this answer? We can Help click Order Now"

For the following research paper assignment, you have been asked to perform an evaluation of employee exposures at a small automobile parts manufacturing facility. The manufacturing processes include two metal presses, two machining stations, three welding stations, a small paint booth, and a shipping/receiving area. There are two employees working at each press, one person working at each machining station, one person working at each welding station, two people working in the paint booth, and four employees working in the shipping/receiving area. One of the presses is a 2,000-ton press, and the other press is a 200-ton press. The 2,000-ton press is the greatest noise source for the facility. The machining area uses a metal working fluid. The safety data sheet (SDS) for the metal working fluid is attached here. All welding is performed on stainless steel. The painting booth uses a powder coating operation, but the employees use xylene and methyl ethyl ketone (MEK) to clean the parts prior to the powder coating operation. At the end of the shift, one of the employees uses 1,3 butadiene to clean the nozzles for the paint booth. The facility uses two electric forklifts to move materials between the production area and the storage warehouse and between the warehouse and the shipping area. All employees work an 8-hour shift.

Part 1: Using the information on anticipation and control we studied in the textbook, identify the hazards that are present in the facility. In your discussion, explain why you chose the hazards, and describe whether you believe the hazards to be actual hazards or potential hazards (which require further evaluation). Describe the specific location(s) at the facility where the hazards are located, and determine how many employees are potentially at risk in those areas. Your response for Part 1 should be at least one page in length.

Part 2: Using the information on evaluation that we studied in the textbook, summarize how you would measure the personal exposures to the hazards that you identified in Part 1. Use the Occupational Safety and Health Administration (OSHA) website (https://www.osha.gov/dts/sltc/methods/toc.html) or the National Institute for Occupational Safety and Health (NIOSH) website (http://www.cdc.gov/niosh/docs/2003-154/default.html) to select the specific sampling and analytical method that would work best to evaluate any chemical hazards you identified. Provide a summary of the sampling media you would use, include the sampling flow rate, discuss how long you would sample, and explain how you would calibrate the sampling train. Include a discussion about why you selected the specific sampling and analytical method.

Part 3: Access the attached sampling results here. For each set of results, perform the following actions: Calculate the 8-hour time weighted average (TWA) exposure. Compare the results to the appropriate OSHA permissible exposure limit (PEL). Determine which results exceed an established OSHA PEL. Write a one-page summary of the sampling results; document the exposures that exceeded an OSHA PEL, and identify those areas that you believe will require the application of controls to reduce risk. Include your calculations, include a list of the OSHA PELs you compared the results to, and explain how you decided that an exposure exceeded an OSHA PEL.

Laboratory Results for Unit VIII Research Paper

Employee Position Analyte Sample Time Sample Result 1 Machining Mineral oil mist 480 minutes 1.1 mg/m3 2 Machining Mineral oil mist 480 minutes 0.9 mg/m3 3 Welding Cleaning Hexavalent chromium 360 minutes 120 minutes 8.5 µg/m3 0.5 µg/m3 4 Welding Cleaning Hexavalent chromium 300 minutes 180 minutes 10.0 µg/m3 0.2 µg/m3 5 Paint Booth Xylene MEK 480 minutes 24 ppm 60 ppm 6 Paint Booth/Cleaning Nozzles 1,3 butadiene 15 minutes 6.0 ppm

Noise Dosimetry Data

Employee Position Sample Time Sample Result 1 Setting up parts for press Operating 2,000-ton press Clean-up 60 minutes 400 minutes 20 minutes 82.0 dBA 100 dBA 80.0 dBA 2 Setting up parts for press Operating 200-ton press Clean-up 30 minutes 430 minutes 20 minutes 80.0 dBA 89.0 dBA 80.0 dBA 3 Machining 480 minutes 85.5 dBA 4 Paint Booth 480 minutes 80.5 dBA 5 Shipping/Receiving/Forklift Driver 480 minutes 82.0 dBA

Part 4: Using OSHA’s hierarchy of controls, recommend the control methods that you believe would be the most effective for reducing the risks associated with the exposures that exceeded the OSHA PEL above. Explain how you would implement the controls and how you would evaluate the effectiveness of the controls. Also, discuss any interim control methods you would recommend for the facility. This section should be at least one page in length. Include a reference page and in-text citations for all sources you used in this project, including your textbook, using proper APA format.

 

"Are you looking for this answer? We can Help click Order Now"

For the following research paper assignment, you have been asked to perform an evaluation of employee exposures at a small automobile parts manufacturing facility. The manufacturing processes include two metal presses, two machining stations, three welding stations, a small paint booth, and a shipping/receiving area. There are two employees working at each press, one person working at each machining station, one person working at each welding station, two people working in the paint booth, and four employees working in the shipping/receiving area. One of the presses is a 2,000-ton press, and the other press is a 200-ton press. The 2,000-ton press is the greatest noise source for the facility. The machining area uses a metal working fluid. The safety data sheet (SDS) for the metal working fluid is attached here. All welding is performed on stainless steel. The painting booth uses a powder coating operation, but the employees use xylene and methyl ethyl ketone (MEK) to clean the parts prior to the powder coating operation. At the end of the shift, one of the employees uses 1,3 butadiene to clean the nozzles for the paint booth. The facility uses two electric forklifts to move materials between the production area and the storage warehouse and between the warehouse and the shipping area. All employees work an 8-hour shift.

Part 1: Using the information on anticipation and control we studied in the textbook, identify the hazards that are present in the facility. In your discussion, explain why you chose the hazards, and describe whether you believe the hazards to be actual hazards or potential hazards (which require further evaluation). Describe the specific location(s) at the facility where the hazards are located, and determine how many employees are potentially at risk in those areas. Your response for Part 1 should be at least one page in length.

Part 2: Using the information on evaluation that we studied in the textbook, summarize how you would measure the personal exposures to the hazards that you identified in Part 1. Use the Occupational Safety and Health Administration (OSHA) website (https://www.osha.gov/dts/sltc/methods/toc.html) or the National Institute for Occupational Safety and Health (NIOSH) website (http://www.cdc.gov/niosh/docs/2003-154/default.html) to select the specific sampling and analytical method that would work best to evaluate any chemical hazards you identified. Provide a summary of the sampling media you would use, include the sampling flow rate, discuss how long you would sample, and explain how you would calibrate the sampling train. Include a discussion about why you selected the specific sampling and analytical method.

Part 3: Access the attached sampling results here. For each set of results, perform the following actions: Calculate the 8-hour time weighted average (TWA) exposure. Compare the results to the appropriate OSHA permissible exposure limit (PEL). Determine which results exceed an established OSHA PEL. Write a one-page summary of the sampling results; document the exposures that exceeded an OSHA PEL, and identify those areas that you believe will require the application of controls to reduce risk. Include your calculations, include a list of the OSHA PELs you compared the results to, and explain how you decided that an exposure exceeded an OSHA PEL.

Laboratory Results for Unit VIII Research Paper

Employee Position Analyte Sample Time Sample Result 1 Machining Mineral oil mist 480 minutes 1.1 mg/m3 2 Machining Mineral oil mist 480 minutes 0.9 mg/m3 3 Welding Cleaning Hexavalent chromium 360 minutes 120 minutes 8.5 µg/m3 0.5 µg/m3 4 Welding Cleaning Hexavalent chromium 300 minutes 180 minutes 10.0 µg/m3 0.2 µg/m3 5 Paint Booth Xylene MEK 480 minutes 24 ppm 60 ppm 6 Paint Booth/Cleaning Nozzles 1,3 butadiene 15 minutes 6.0 ppm

Noise Dosimetry Data

Employee Position Sample Time Sample Result 1 Setting up parts for press Operating 2,000-ton press Clean-up 60 minutes 400 minutes 20 minutes 82.0 dBA 100 dBA 80.0 dBA 2 Setting up parts for press Operating 200-ton press Clean-up 30 minutes 430 minutes 20 minutes 80.0 dBA 89.0 dBA 80.0 dBA 3 Machining 480 minutes 85.5 dBA 4 Paint Booth 480 minutes 80.5 dBA 5 Shipping/Receiving/Forklift Driver 480 minutes 82.0 dBA

Part 4: Using OSHA’s hierarchy of controls, recommend the control methods that you believe would be the most effective for reducing the risks associated with the exposures that exceeded the OSHA PEL above. Explain how you would implement the controls and how you would evaluate the effectiveness of the controls. Also, discuss any interim control methods you would recommend for the facility. This section should be at least one page in length. Include a reference page and in-text citations for all sources you used in this project, including your textbook, using proper APA format.

 

"Are you looking for this answer? We can Help click Order Now"

For the following research paper assignment, you have been asked to perform an evaluation of employee exposures at a small automobile parts manufacturing facility. The manufacturing processes include two metal presses, two machining stations, three welding stations, a small paint booth, and a shipping/receiving area. There are two employees working at each press, one person working at each machining station, one person working at each welding station, two people working in the paint booth, and four employees working in the shipping/receiving area. One of the presses is a 2,000-ton press, and the other press is a 200-ton press. The 2,000-ton press is the greatest noise source for the facility. The machining area uses a metal working fluid. The safety data sheet (SDS) for the metal working fluid is attached here. All welding is performed on stainless steel. The painting booth uses a powder coating operation, but the employees use xylene and methyl ethyl ketone (MEK) to clean the parts prior to the powder coating operation. At the end of the shift, one of the employees uses 1,3 butadiene to clean the nozzles for the paint booth. The facility uses two electric forklifts to move materials between the production area and the storage warehouse and between the warehouse and the shipping area. All employees work an 8-hour shift.

Part 1: Using the information on anticipation and control we studied in the textbook, identify the hazards that are present in the facility. In your discussion, explain why you chose the hazards, and describe whether you believe the hazards to be actual hazards or potential hazards (which require further evaluation). Describe the specific location(s) at the facility where the hazards are located, and determine how many employees are potentially at risk in those areas. Your response for Part 1 should be at least one page in length.

Part 2: Using the information on evaluation that we studied in the textbook, summarize how you would measure the personal exposures to the hazards that you identified in Part 1. Use the Occupational Safety and Health Administration (OSHA) website (https://www.osha.gov/dts/sltc/methods/toc.html) or the National Institute for Occupational Safety and Health (NIOSH) website (http://www.cdc.gov/niosh/docs/2003-154/default.html) to select the specific sampling and analytical method that would work best to evaluate any chemical hazards you identified. Provide a summary of the sampling media you would use, include the sampling flow rate, discuss how long you would sample, and explain how you would calibrate the sampling train. Include a discussion about why you selected the specific sampling and analytical method.

Part 3: Access the attached sampling results here. For each set of results, perform the following actions: Calculate the 8-hour time weighted average (TWA) exposure. Compare the results to the appropriate OSHA permissible exposure limit (PEL). Determine which results exceed an established OSHA PEL. Write a one-page summary of the sampling results; document the exposures that exceeded an OSHA PEL, and identify those areas that you believe will require the application of controls to reduce risk. Include your calculations, include a list of the OSHA PELs you compared the results to, and explain how you decided that an exposure exceeded an OSHA PEL.

Laboratory Results for Unit VIII Research Paper

Employee Position Analyte Sample Time Sample Result 1 Machining Mineral oil mist 480 minutes 1.1 mg/m3 2 Machining Mineral oil mist 480 minutes 0.9 mg/m3 3 Welding Cleaning Hexavalent chromium 360 minutes 120 minutes 8.5 µg/m3 0.5 µg/m3 4 Welding Cleaning Hexavalent chromium 300 minutes 180 minutes 10.0 µg/m3 0.2 µg/m3 5 Paint Booth Xylene MEK 480 minutes 24 ppm 60 ppm 6 Paint Booth/Cleaning Nozzles 1,3 butadiene 15 minutes 6.0 ppm

Noise Dosimetry Data

Employee Position Sample Time Sample Result 1 Setting up parts for press Operating 2,000-ton press Clean-up 60 minutes 400 minutes 20 minutes 82.0 dBA 100 dBA 80.0 dBA 2 Setting up parts for press Operating 200-ton press Clean-up 30 minutes 430 minutes 20 minutes 80.0 dBA 89.0 dBA 80.0 dBA 3 Machining 480 minutes 85.5 dBA 4 Paint Booth 480 minutes 80.5 dBA 5 Shipping/Receiving/Forklift Driver 480 minutes 82.0 dBA

Part 4: Using OSHA’s hierarchy of controls, recommend the control methods that you believe would be the most effective for reducing the risks associated with the exposures that exceeded the OSHA PEL above. Explain how you would implement the controls and how you would evaluate the effectiveness of the controls. Also, discuss any interim control methods you would recommend for the facility. This section should be at least one page in length. Include a reference page and in-text citations for all sources you used in this project, including your textbook, using proper APA format.

"Are you looking for this answer? We can Help click Order Now"

Answers

Related Questions

Term Paper...

Term Paper Project: Designing a Secure NetworkDue Week 10 and worth 190 pointsThis term paper involves putting together the various concepts learned t...

Nursing Finances...

 To prepare:Review the Learning Resources for this week, focusing on the role of nurse managers in making financial decisions.Conduct additional rese...

STAT 200...

Search for an article about "Replication Crisis" (you may use Wikipedia's if you like).What does this "crisis" refer to? (what does it mean for "k...

For Kim Woods Only...

 Week 10 Discussion"Virtualization & Memory" Please respond to the following:From the e-Activity, examine at least three (3) benefits and three (3) d...

FolderM4 Assignment psy...

 Hide Submission Folder InformationSubmission FolderM4 Assignment 2 SubmissionsInstructionsAssignment 2: Correlation and RegressionA human resources...

T-TEST...

 Assignment 2: RA 1: t-TestsWorking with Data in Microsoft ExcelOnce again, reading about t-test statistics and descriptive statistics is one thing....

Assignment 2: Descriptive Statistics and Industria...

 Descriptive statistics and graphical data presentations formulate the initial phase of statistical analysis. With these tools, the industrial/organi...

Expansionary Fiscal Policy...

 In an effort to move the economy out of a recession, the federal government would engage in expansionary economic policies. Respond to the following...

Recruitment and Development of Future Leaders...

 Your company's Vice President of Human Resources has approached your team for assistance in recruiting and developing your organization's fu...

Unit I Essay and Journal Entry...

EssayFor this assignment, you will be discussing the concepts covered in this unit and how these concepts can affect the community in which you curren...

Strategic Management Process...

 The purpose of this assignment is to help students understand strategic business terminology (vision, mission, goals, objectives, specific objective...

Multi Step Income Statement...

 Prepare a correct detailed multiple-step income statement.  Assume a tax rate of 25%.WRIGHT COMPANYIncome StatementFor the Month Ended December 31,...

Organisational Change Management...

 Coursework containing 3 elements ( 3000 words in total consisting of three 1000 words elements) Element 01 - How and why can managers apply complex...

Hw due in 14 hours...

For this assignment, write an analysis of three different aviation positions (pilot, dispatcher, mechanic, ATC, CEO, CFO, etc.). Whatever you want to...

Product Life Cycle...

 Incorporate a product strategy that addresses the following:At least three areas of the product life cycle (NPI-new product introduction, growth, ma...

Linguistics...

20Entry # Date What did you observe outside class? Field of linguistics (phonology, morphology, etc.) and concept from class which this exemplifies. ...

Technology and Social Change...

 Review the list of Films on Demand: Sociology Collection: Social Institutions to select and watch one video from each of the following categories li...

CMIT Week 7...

In this section, address each of the following.Identify network services needed.List additional servers or network devices needed to implement the net...

Fluid Mechanics...

1. Explain about the below terminologies.a.  1 pa ( pressure unit )b- Lift coefficient c- Drag coefficient d- Pressure coefficiente- Mach Number. ...

Science in news...

Now that you have been learning about science, you may have noticed news articles or online videos on various scientific topics. Science is all around...

U.S Criminal Justice Process...

 The constitutional rights guaranteed in the Bill of Rights are most highly protected during the trial stage of a criminal proceeding. This is when t...

CIS...

 PART 1: THE Social Media assignment - 25 pointsComplete the following:To prepare you the assignment, listen and watch the following video (closed ca...

Identify a department issue observed in your curre...

Identify a department issue observed in your current or prior work experience or a work related issue observed as a consumer. As a departmental manage...

This assignment consists of two...

Assignment 2: Marketing PlanDue Week 6 and worth 100 pointsThis assignment consists of two (2) sections: a marketing plan and sales strategy, and a ma...

If you didn't find the right answer

Ask Your Questions, We'll notify you once someone answers it